Microwave Forum

anee · Guest

hello
how much output of square wave will be eoungh for POS1060 as you write the input is 17-22v and 17 -23v in figer? i will be thx,s ful if u help me configration of POS1060

input is Vcc=10v

tune input=?

can u plesae tell me about the PA and pin,s information

i have this

anee · Guest

as i notes while watching datasheet of pos1060

Pin Connections Port RF OUT V-CC V-TUNE GND EXT

hx 2 1 8 3,4,5,6,7

and u take Vcc as pin 5 tune input as pin 4 and RF out as 1

richy_64 · Administrator Messages: 198

Hi anee,
what are the product codes of these pa´s?
I only can see that they come from Motorola.

--------------------
Pin Connections Port RF OUT V-CC V-TUNE GND EXT
hx 2 1 8 3,4,5,6,7
and u take Vcc as pin 5 tune input as pin 4 and RF out as 1

...good question...

Gast · Created: 2004-08-30, 04:18 PM CET Subject: Re: help to understand POS1060

sorry for bad typing i guess i mena to say

as datashee of POS1060 say,s

Pin Connections Port RF OUT V-CC V-TUNE GND EXT

hx 2 1 8 3,4,5,6,7

and your cricuit showing different

and plesae tell me the output of square wave needed to feed POS1060

Gast · Created: 2004-08-30, 04:20 PM CET Subject: Re: help to understand POS1060

i Pin Connections Port RF OUT= 2 V-CC= 1 V-TUNE=8
GND EXT = 3,4,5,6,7

i dont know y my writing change after post

kleiner-onkel · Administrator Messages: 412 Location: South-West-G

these blue amplifier moduls are just from old Germany C-NET analog Phones which is cut down since 3 Years . Frequency band was around 450 to 460 Mhz and not intend to the picture.

Chris

Gast · Created: 2004-09-01, 01:31 AM CET Subject: Re: help to understand POS1060

hi
what about POS1060 pin configration

kleiner-onkel · Administrator Messages: 412 Location: South-West-G

keep looking after ----> Minicircuits homepage

Gast · Created: 2004-09-01, 07:53 PM CET Subject: Re: help to understand POS1060

how much input need to feed Pf1040 at pin # 1 which is coming from POS1060 .......as u use

Voltage Regulator L7810 (for VCO)
1 Voltage Regulator L7805 (for Power Fet)

kleiner-onkel · Administrator Messages: 412 Location: South-West-G

thant's all right. The VCO need around 30mA
so it's possible to take a small 78L10

The Power AMP need at least a 78M05 (500mA max.)
or better a 7805 (1A)
or 78L05 (2A)

pos 1060 pin conections

from top/left to right
1. RF out
2. Ground
3. Ground
4. LF in

from bottom/left to right
5. VCC
6. Ground
7. Ground
8. Ground

Chris

immy · Guest

i hope ur new noise-gen witn ‘non-inverting’ 741 will work .....i just have 5 day to submit the project ....1 rquest to all of u help me as much as u can .....

the datasheet saying POS1060 will tune at 930 at 10V to 12 V

how strong with POS1060 should be to work fine ......y 555 time will not work or square wave......as ur jammer 1 it work

plesae reply all the qustions its request .... i m in tension bcoz of the 5 days to submit the project and i m still working in noise-gen